MakerBot Replicator 2x Guía de usuario descargar pdf (Pagina 35)

1. Locate the X-axis pulley. It is attached to

the motor mounted on the right side of the

gantry. Slide the extruders to the le until

you have access to the set screw holding

the pulley to the motor sha. Use the

1.5mm hex wrench from the Accessory Box

to tighten the set screw. [Fig 2.11]

2. Locate the Y-axis pulley. It is attached to the

motor mounted in the back right corner of the

Replicator 2X. Slide the extruders to the front

of the Replicator 2X until you have access to

the set screw holding the pulley to the motor

sha. Use the 1.5mm hex wrench from the

Accessory Box to tighten the set screw.

NOTE: To view a video of this process, go to http://

www.youtube.com/watch?v=76XaGlyG0Z0

REALIGNING THE GANTRY CONTINUED

35MAINTENANCE

6. Use the 1.5 mm hex wrench to tighten the

set screw in each of the two back pulleys.

Make sure these set screws are very tight.

NOTE: If you cannot see one of the set screws, hold

both sides of the gantry and gently push it away from

the front of the MakerBot Replicator 2X. Make sure

to exert an equal amount of pressure on both sides

of the gantry. Push only until you can see the hidden

set screw.

7. Manually move the extruders toward the

back of the MakerBot Replicator 2X. Make

sure the gantry is as far back as it can go.

8. Use the 1.5 mm hex wrench to tighten the

set screw in each of the two front pulleys.

Make sure these set screws are very tight.

NOTE: If you cannot see one of the set screws, hold

both sides of the gantry and very gently push it

away from the back of the MakerBot Replicator 2X.

Make sure to exert an equal amount of pressure on

both sides of the gantry. Push only until you can see

the hidden set screw.

When you have completed these steps, your

gantry will be correctly aligned again.

NOTE: To view a video of this process, go to http://

www.youtube.com/watch?v=NP47vjSZQtA

TIGHTENING THE X-AXIS PULLEY AND THE Y-AXIS PULLEY

Loose X and Y-axis pulleys in your MakerBot Replicator 2X can result in belts slipping during printing.

If you notice shis on the X or Y-axis during a print, it might be time to tighten your pulleys. To do this:

Fig. 2.11

X-axis

pulley

1 2 ... 30 31 32 33 34 35 36 37 38 39 40

Comentarios a estos manuales

Sin comentarios

Compass Warp360 User Manual (79 pages)

Brand: Compass | Category: Air equipment | Size: 9.05 MB |

Version 05/13

Content / Inhaltsverzeichnis

Introduction

Warranty

AMA Information

R/C Helicopter Safety

Einleitung

Gefahren

Garantie

Nationaler Modellflugverband

Main Blade Grips (2x)

Swashplate

Swashplate 1

Swash Driver (2x)

Rotor Head 1

Rotor Head 2

Swashplate 2

Tail Case 1

Tail Case 2

Tail Case 3

Tail Control Arm

Tail Grip

Tail Rotor Hub 1

Tail Rotor Hub 2

Tail Pitch Slider

Tail Rotor 1

Tail Rotor 2

Radio Tray

Lower Bearing Block

Upper Bearing Block

Servo Mount

Servo Arm 15mm (3x)

Servo Arm 12mm

Belt Tensioner

Tail Control Rod

Autorotation Hub

Main Pulley 1

Main Pulley 2

Motor Mount

Side Frame Left 1

Side Frame Right

Elevator Servo

Battery Tray Assembly

Belt Tensioner Assembly

Upper Bearing Block Assembly

Lower Bearing Block Assembly

Servo Mount Assembly

Frame Support

Radio Tray Assembly

Motor Mount Assembly 1

Tail Boom Holder Assembly

Side Frame Left to Right 1

Side frame Left to Right 2

Motor Mount Assembly 2

Canopy Mount Assembly

Struts Assembly

Tail Control Rod Assembly 1

Tail Control Rod Assembly 2

Tail Boom Assembly

Mast Lock Collar

Main Shaft Assembly 1

Main Belt Assembly

Gear Spacer Assembly

Main Pulley Assembly

RC-Equipment

Servo Arm Assembly

Swash Guide

Swash Rods

Swash Link Assembly

Swash Guide Assembly

Battery Assembly

Rudder Servo Setup

Mode 1 Mode 2

Flybarless-Setup

Flybarless Setup

www.compassmodel.com

More products and manuals for Air equipment Compass

Models	Document Type
None

MakerBot Replicator 2x Guía de usuario Pagina 35

Comentarios a estos manuales

Compass Warp360 manuals

Compass Warp360 User Manual (79 pages)

Table of contents

More products and manuals for Air equipment Compass

MakerBot Replicator 2x Guía de usuario Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo MakerBot Replicator 2x

Compass Warp360 manuals

Compass Warp360 User Manual (79 pages)

Table of contents

More products and manuals for Air equipment Compass